How to Replace Particle Board Under Sink Step-by-Step
With the passage of time, every installed fixture and material can be faulted. We need to replace it with a new one when it becomes faulty.
But today, our question is how to replace particle board under the sink.
Because replacing the particle board under the sink can be a difficult task for any beginner.
But we can tackle it with the right guidance at the right time.
Particle board is affordable and easy to install, but it can be damaged under the sink cabinets due to moisture and wear over time. Therefore, we will replace it.
In this article, I will guide a step-by-step process to replace the particle board under the sink from preparation to finish.
So, keep reading.
Tools and Materials to Replace Particle Board Under Sink
The right tool at the right time can help us to start the replacement process. Here are some of the right tools and materials to complete the project.
Safety Gear
- Safety goggles
- Gloves
- Dust mask
Tools
- Screwdrivers
- Pliers
- Hand Saw / Circular saw
- Adjustable wrench
- Cordless drill with appropriate bits
- Measuring tape
Materials
- New particle board
- wood screws
- wood glue
- Towel
These items will help to save your time and ensure you’re well-equipped for the job.
Safety Precautions to Replace Particle Board Under Sink
Before starting any kind of project, it is necessary to ensure all the safety precautions. Without safety, any mishap can occur.
Here are some safety precautions.
- Wear safety goggles during the process to protect the eyes from dust and debris.
- Use gloves to protect the hands from sharp edges.
- Wear a mask to prevent inhalation of particles.
- If your sink area has electrical outlets, turn off the power switch.
- Ensure proper ventilation in the workspace to disperse dust and fumes.
Removing the Old Particle Board
After ensuring the safety precautions, it’s time to remove the old particle board under the sink.
We will break the whole procedure into several sub-steps to understand better.
1- Disconnecting Plumbing
- First, we will turn the water supply off towards the sink. Commonly turn off valves located under the sink. Turn them clockwise, and the water supply will be stopped.
- Place a towel under the sink to prevent spreading the remaining water. Use pliers to lose the nuts and disconnect the drain pipes.
- If we have a connection of hot and cold water, disconnect the connections from the faucet using a wrench.
Note: Be sure that all the connection has disconnected.
2- Removing Fixtures
- Using the wrench, loosen the nuts of the faucet and remove it carefully from the sink.
- If we have multiple additional fixtures with sinks, like soap dispensers and garbage disposal, disconnect all of them and remove them carefully.
3- Dismantling the Old Board
- If the sink cabinet has a back panel, we will remove it first to access the old particle board.
- Remove all the nails or screws attached to the cabinet and particle board with the help of a screwdriver or cordless drill.
- Remove the old particle board from the cabinet frame carefully without damaging the surrounding structure.
Installing the New Particle Board
Installing new particle board is not difficult. Just follow these simple steps and replace particle board under sink.
Here is the step-by-step procedure.
Cutting the Board to Size
- After removing all the old fixtures and materials, we will measure the dimensions of our sink cabinet.
- Measurements should be precise to accurately fit the new particle board at that place.
- Use a saw to cut the new board according to measured correct dimensions.
- To create a strong bond between the particle board and cabinet frame, apply glue around all the edges of the cabinet frame.
- Put the new particle board accurately into the cabinet frame.
- Use wood screws evenly along the edges to secure the board to the cabinet frame.
- Check the level of the particle board using level instruments. If necessary, adjust the levelness.
- Our new particle board is attached and ready to use the sink cabinet.
Reconnecting Plumbing and Fixtures
After the particle board is in place, we will gradually reconnect all the plumbing and fixtures.
- Reattach drain pipes
- Reconnect water lines
- Reinstall fixtures
Finishing Touches
To complete the replacement process, testing and verifying the finishing touches is essential.
Follow these simple steps to verify.
- Turn on the water supply and check for any leaks around the connections. If you notice any, tighten the affected connections.
- Reinstall the back panel securely.
- Clean the sink to ensure it is ready to use without any disturbance.
Conclusion
Replacing particle boards under the sink is a challenging task only for beginners, not for experts.
But, if you follow all the steps mentioned in this article, you can do it easily. Replacing particle boards improves the functionality and durability of our kitchen and bathrooms.
However, using the right tools to replace the particle board is necessary. With the right tools and materials, we can complete any project in time and enjoy the more reliable fixtures for years to come.
I hope you have learned how to replace particle board under sink.
Thank you for your precious time.
Best wishes
Frequently Asked Questions
How do you fix water damaged particle board under a sink?
1.Diconnecting Plumbing
2.Removing Fixtures
3.Dismentling Old Particle Board
4.Cutting and Installing New Particle Board
5.Reconnecting Plumbing and Fixtures
6.You have done it.
Can the bottom of a cabinet be replaced?
Yes, you can replace the bottom floor of cabinet. But it requires patience with skills. If you do it, you can save your cabinet more damage in future.
What kind of wood do you use under a kitchen sink?
Generally 3/4 inch thick plywood sheet used under a kitchen sink, cabinet door and drawers.
Can particle board be repaired?
It depends on the condition of damage. If you are facing little scraches or holes, you can fill them by using wood filler or putty. But incase of big damage, replacing the particle board is better.
How much does it cost to replace wood under a sink?
It also depends on the condition of damage. But average budge of replacing wood under sink is150$ to 200$ including labor and material cost.